GRAS 26HG 1/4" Preamplifier with 3 m Integrated Cable, Low Frequency
Freq range: 1 Hz to 200 kHz
Noise: 1.8 µV Gain: -0.29 dB
Special feature: For low frequency and low-noise applications
Technology
Design
All GRAS microphone preamplifiers are based on a small ceramic thick-film substrate with a very high input impedance. The ceramic substrate is shielded by a guard ring to minimise the influence of stray capacitance and microphonic interference.
The casing is made of stainless steel for maximum strength and durability. The small dimensions of this preamplifier ensure reliable operation under humid conditions owing to the heat generated by internal power dissipation.
Dynamic Range
Type 26HG can handle both single and dual-sided power supplies. The supply can vary between 28 VDC and 120 VDC single-sided or ±14VDC and±60 VDC dual-sided. When using the high supply voltage (120VDC or ±60VDC), the dynamic range exceeds 140 dB.
Noise
The electrical circuit in Type 26HG preamplifier is built on a ceramic substrate using selected low noise components to gain very low self-noise. The electrical self-noise is so low that system noise is mainly determined by the microphone capsule’s thermal noise.
Frequency response
The low-frequency cut-off of the Type 26HG preamplifier is mainly determined by the input impedance of the preamplifier and the capacitance of the microphone capsule. The capacities 20 pF,6.5 pF and 3 pF equal the typical capacitances of 1/2", 1/4" and 1/8" microphone capsules respectively.
The high-frequency cut-off is determined by the preamplifier’s ability to drive capacitive loads (slewrate), caused by the cable. For large-signals, the effects of these parameters must be accounted for when measurements are performed. The large-signal response for Type 26HG for various capacitive loads corresponding to different cable lengths is shown in the data sheet. The output level is in decibels relative to 1 Volt. Typical capacitance for the cable is 100 pF/m(30 pF/foot).
Type 26HG is typically used with a Type 40AN low frequency microphone capsule to reach a -3-dB cut-off frequency around 0.25 Hz.
Connector
Preamplifier Type 26HG is provided with a 3-m lightweight cable terminating in a 7-pin LEMO series 1B plug. The cable is only 2.5 mm in diameter and will withstand temperatures from- 40 oC to +150 oC. An adaptor (GR0010) for GRAS 1/2" microphones is included.
7-pin LEMO plug 1B male (ext. view)
Specifications
Conditions: 23 °C Ambient temperature, ±60V/+120V power supply, 18 pF dummy microphone, 3 m output cable.
Typical frequency response for 1/2" (20 pF), 1/4" (6.5 pF) and 1/8" (3 pF) microphones
Typical max RMS output signal with 120 V and 30 V supply
GRAS Sound & Vibration reserves the right to change specifications and accessories without notice.
Dimensions
Ordering info
Included items
| GRAS GR0010 |
Adapter for 1/4" preamplifier and 1/2" microphone |
Optional items
| GRAS AA0008 |
3 m LEMO 7-pin - LEMO 7-pin Cable |
|
Customized Length LEMO 7-pin - LEMO 7-pin Cable |
|
|
1/4" Microphone Holder, POM |
|
|
1/4" Microphone Holder, Stainless Steel |
|
|
Swivel head |
|
| GRAS AL0006 |
Tripod |
|
Adapter for 1/8" microphone and 1/4" preamplifier |
|
| GRAS RA0006 |
Right-angled (90º) Adapter for 1/4" Microphone and 1/4" Preamplifier |
|
6pF Preamplifier-input adapter for 1/4" microphones |
|
|
2-Channel Power Module with gain, filters and SysCheck generator |
|
|
2-Channel Universal Power Module with signal conditioning and PC interface |
GRAS Sound & Vibration reserves the right to change specifications and accessories without notice.
