GRAS 26AA Set 1/4" Preamplifier with Integrated Cable for Intensity Probes

Freq range: 2.5 Hz - 200 kHz
Noise: 1.8 µV
Gain: -0.29 dB
Special feature: For GRAS intensity probe handles with 4-pin LEMO connectors

The 1/4" Preamplifier Set with Integrated Cable for Intensity Probes are two small robust units optimized for acoustic measurements using condenser microphones. The set has a very low inherent noise level, a wide dynamic range and a frequency response from below 2 Hz to above 200 kHz.

Technology

Design

All GRAS microphone preamplifiers are based on a small ceramic thick-film substrate with a very high input impedance. The ceramic substrate is shielded by a guard ring to minimize the influence of stray capacitance and microphonic interference. The casing is made of stainless steel for maximum strength and durability. The small dimensions of this preamplifier ensure reliable operation under humid conditions owing to the heat generated by internal power dissipation.

Dynamic Range

26AA can handle both single and dual-sided power supplies. The supply can vary between 28 and 120 VDC single-sided or ±14 and ±60 VDC dual-sided. When using the high supply voltage (120 VDC or ±60 VDC), the dynamic range exceeds 140 dB.

Noise

The electrical circuit in 26AA is built on a ceramic substrate using selected low-noise components to gain very low self-noise. The electrical self-noise is so low that system noise is mainly determined by the microphone capsule’s thermal noise.

Frequency response

The low-frequency cut-off of the 26AA preamplifier is mainly determined by the input impedance of the preamplifier and the capacitance of the microphone capsule. The capacities 20, 6.5, and 3 pF equal the typical capacitances of ½, ¼, and ⅛ microphone capsules respectively. The high-frequency cut-off is determined by the preamplifier’s ability to drive capacitive loads (slew rate), caused by the cable. For large signals, the effects of these parameters must be accounted for when measurements are performed. The output level is in decibels relative to 1 Volt. The typical capacitance for the cable is 100pF/m (30pF/ft).

Connector

GRAS 26AA Preamplifier is supplied with a 30 cm cable terminating in a 4-pin LEMO plug. It is for use with the GRAS Intensity Probe 50AI. Two extension cables are available:

  1. AA0006—2 m, 4-pin LEMO series 0B (female) connector at one end and a 4-pin LEMO (male) series 0B plug at the other end.
  2. AA0007—2 m, 4-pin LEMO series 0B (female) connector at one end and a 7-pin LEMO (male) series 1B plug at the other end.

Specifications

Frequency range (±0.2 dB) with 18 pF microphone dummy
Hz
2.5 to 200 k
Slew rate
V/µs
20
Output impedance
Ω
75
Output Voltage Swing, max. @ ±14V/+28V power supply
Vp
12
Output Voltage Swing, max. @ ±60V/+120V power supply
Vp
50
Noise (A-Weighted) max.
µV
2.5
Noise (A-Weighted) typ.
µV
1.8
Noise (Linear 20 Hz – 20 kHz) max.
µV
6
Noise (Linear 20 Hz – 20 kHz) typ.
µV
3.5
Gain
dB
-0.29
Power supply, single
V
28 to 120
Power supply, balanced
V
±14 to ±60
DC-offset, min., single suppy
V
0.5 x Vs - 1
DC-offset, max., single suppy
V
0.5 x Vs + 4
DC-offset, balanced supply
V
-1 to 4
Temperature range, operation
°C / °F
-30 to 70 / -22 to 158
Temperature range, storage
°C / °F
-40 to 85 / -40 to 185
Humidity range non condensing
% RH
0 to 95
Connector type
4-pin LEMO (FGG.0B.304)
CE/RoHS compliant/WEEE registered
Yes / Yes, Yes
Weight
g / oz
22.0 / 0.78

Conditions: 23 °C Ambient temperature, ±60V/+120V power supply, 18 pF dummy microphone, 3 m output cable.

GRAS Sound & Vibration reserves the right to change specifications and accessories without notice.

Dimensions